Uniaxial Compressive Strength Of Rock

Uniaxial Compressive Strength - an overview ...

Uniaxial compressive strength (UCS) is a key physical test relevant to iron ore crusher design and rock geomechanics for mining. Tests are typically performed on intact lengths of NQ, HQ, or PQ diamond drill core and record the maximum axial load sustained at the point of failure.

Compressive strength of rocks - PetroWiki

Estimating compressive strength. General rock failure criterion can be reduced to a few parameters dependent on lithology (m) and the uniaxial compressive strength (C 0). Lithology is commonly derived during log analysis, so m may be estimated (Table 1). What is needed still is an initial measure of rock strength provided by C 0.

(PDF) The Uniaxial Compressive Strength of Soft Rock

Soft rock is a term that usually refers to a rock material with a uniaxial compressive strength (UCS) less than 20 MPa. This low strength range might be influenced by physical characteristics ...

Unconfined Compressive Strength Test of Rock

This test method specifies the apparatus, instrumentation, and procedures for determining unconfined compressive strength of intact rock core specimens. This procedure is identical to ASTM D 2938 except that the cores are tested after cutting without grinding, and neoprene caps are used on …

Where is used the uniaxial compressive strength?

Where is used the uniaxial compressive strength? uniaxial compressive strength is common test in rock mechanics. this test is very important and so far many relationships are provided to predict it.

8. STRENGTH OF SOILS AND ROCKS

strength is the most commonly measured strength parameter and this is also true of rock specimens. For the uniaxial or unconfined compressive strength test a right circular cylinder of the material is compressed between the platens of a testing machine as illustrated in Fig. 8.1. The compressive strength is then defined as the maximum load ...

THE UNIAXIAL COMPRESSIVE STRENGTH OF SOFT ROCK

THE UNIAXIAL COMPRESSIVE STRENGTH OF SOFT ROCK D. S. Agustawijaya Lecturer, Department of Civil Engineering, Faculty of Engineering, Mataram University, Mataram, Indonesia Email: [email protected] ABSTRACT Soft rock is a term that usually refers to a rock material with a uniaxial compressive strength (UCS) less than 20 MPa.

STRENGTH PROPERTIES OF ROCKS AND ROCK MASSES 1 ...

STRENGTH PROPERTIES OF ROCKS AND ROCK MASSES 1. INTRODUCTION 2. TESTING OF INTACT ROCK FOR STRENGTH 2.1 Uniaxial Compression 2.2 Point Load Testing 2.3 Uniaxial Tension 2.4 Indirect Tension Tests 2.5 Shear Tests 2.6 Confined Compression Tests (Triaxial Tests) 2.7 Biaxial and Multiaxial Tests 2.8 Other Tests 3. PARAMETERS AFFECTING ROCK STRENGTH 4.

uniaxial compressive strength - Schlumberger Oilfield Glossary

The uniaxial compressive strength (UCS) is the maximum axial compressive stress that a right-cylindrical sample of material can withstand before failing. It is also known as the unconfined compressive strength of a material because confining stress is set to zero.

MinE 323- Uniaxial Compressive Strength Test (Lab 4) - YouTube

9/7/2018· MinE 323- Uniaxial Compressive Strength Test (Lab 4) ... Testing rock specimen for Uniaxial Compressive Strength - Duration: 3:30. Gipfel Gear 4,907 views. 3:30.

Suggested Methods for Determining the Uniaxial Compressive ...

Suggested Methods for Determining the Uniaxial Compressive Strength and Deformability of Rock Materials PART 1. SUGGESTED METHOD FOR DETERMINATION OF THE UNIAXIAL COMPRESSIVE STRENGTH OF ROCK MATERIALS 1. SCOPE This method of test is intended to measure the uni- axial compressive strength of a rock sample in the form

ASTM D7012 - 14e1 Standard Test Methods for Compressive ...

5.2 Method C, uniaxial compressive strength of rock is used in many design formulas and is sometimes used as an index property to select the appropriate excavation technique. Deformation and strength of rock are known to be functions of confining pressure. Method A, triaxial compression test, is commonly used to simulate the stress conditions under which most underground rock masses exist.

Correlation between Uniaxial Compressive Strength and ...

different rock formations of the Salt Range area of Pakistan were tested to evaluate the correlations between the uniaxial compressive strength and the corresponding values of the point load index. Two hundred rock cores were drilled and used for the uniaxial compressive strength …

Uniaxial compressive strength ( c) and deformation modulus ...

Uniaxial compressive strength ( c), E-modulus and the factor m i in the Hoek-Brown failure criterion for rock masses Average values from tests Tests of rocks world of intact rock samples -wide* Scandinavian rocks tested at SINTEF / NTNU *** Rating of the factor m i ** c E E c Number of tests c E E c Number

unconfined compressive strength - Schlumberger Oilfield ...

The unconfined compressive strength (UCS) is the maximum axial compressive stress that a right-cylindrical sample of material can withstand under unconfined conditions—the confining stress is zero. It is also known as the uniaxial compressive strength of a material because the application of compressive stress is only along one axis—the longitudinal axis—of the sample.

Estimation of uniaxial compressive strength of rock ...

Evaluation of simple methods for assessing the uniaxial compressive strength of rock. International Journal of Rock Mechanics and Mining Science 38, 981–994. Kahraman, S., Gunaydin, O., Fener, M., 2005. The effect of porosity on the relation between uniaxial compressive strength …

Unconfined Compression Test | Geoengineer

Table 2: Typical values of Uniaxial Compressive Strength for a various number of rocks (from Attewell & Farmer 1976). References. ASTM D7012-14e1, (2014).Standard Test Methods for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and Temperatures, ASTM International, West Conshohocken, PA.

Measurement of uniaxial compressive strength of rocks ...

The uniaxial compressive strength of intact core specimens (UCS) was plotted against the compressive strength of the reconstructed cores (q u) from rock cuttings (Figs. 2a and b). A reasonable correlation between q u and UCS was found. Accordingly, a …

Uniaxial compressive strength versus Global strength

Uniaxial compressive strength of intact rock sci = 100 MPa Geological Strength Index GSI = 40 Constant mi = 10 Using the program RocLab1, the uniaxial compressive strength of the rock mass is calculated as sc = 3.307 MPa and the failure envelope for this rock mass is plotted in Figure 1.

Compressive strength - Wikipedia

By definition, the ultimate compressive strength of a material is that value of uniaxial compressive stress reached when the material fails completely. The compressive strength is usually obtained experimentally by means of a compressive test. The apparatus used for this experiment is the same as that used in a tensile test. However, rather ...

USING THE POINT LOAD TEST TO DETERMINE THE UNIAXIAL ...

the uniaxial compressive strength (UCS), and to propose appropriate Is50 to UCS conversion factors for different coal measure rocks. The rock strength determined by the PLT, like the load frame strengths that they estimate, are an indication of intact rock strength and not necessarily the strength of the rock mass. THE UNIAXIAL COMPRESSIVE ...

Standard Test Method for Unconfined Compressive Strength ...

ASTM D2938-95(2002), Standard Test Method for Unconfined Compressive Strength of Intact Rock Core Specimens (Withdrawn 2005), ASTM International, West …

Estimate of Uniaxial Compressive Strength of ...

The purpose of this study was to clarify the relationships between results of index tests and uniaxial compressive strength (UCS) in hydrothermally altered soft rocks of the Upper Miocene, which are typical of the soft rock found in northeastern Hokkaido, Japan. Index tests were performed using point load testing machine and needle penetrometer with irregular lump specimens under forced-dry ...

Prediction of the uniaxial compressive strength and ...

Uniaxial compressive strength and tensile strength considered as important parameters in characterization of rock material in rock engineering. The necessary core samples cannot always be obtained from weak and block-in-matrix conglomeratic rock. For this reason, the predictive models can employed for the indirect estimation of mechanical parameters. The study investigated correlations ...

Rock strength from log parameters - PetroWiki

An understanding of rock strength is important for designing recovery plans for a reservoir and for developing an appropriate reservoir simulation.A detailed discussion of rock failure can be found in Rock failure relationships and Compressive strength of rocks.But the data needed for these methods may not be readily available, so there is a desire to use data available from well logs that are ...

POINT LOAD STRENGTH INDEX TEST OF ROCK (IS-8764 ...

Uniaxial compressive strength of rock may be predicted from the following equation. q c = 22*I s50 Mpa. Report. The corrected mean value of the point load strength index I s50 is reported in Mpa. 2. Axial Test Axial Test Procedure. The axial test is conducted on rock core sample of small length.

The Uniaxial Compressive Strength of Soft Rock | Semantic ...

Soft rock is a term that usually refers to a rock material with a uniaxial compressive strength (UCS) less than 20 MPa. This low strength range might be influenced by physical characteristics, such as size, saturation, weathering and mineral content.

ISRM

In the ISRM website you will find information about the activities of the society as well as information and services useful to the rock mechanics practitioners, such as a conference directory, ... Uniaxial Compressive Strength and Deformability of Rock Materials ...

Rock Mechanics

Compressive Strength!! Tensile strength = resistance to failure under tensile stress ! Typically much lower than compressive strength • 10% of compressive strength typical (Table 7.2) ! Horizontal rock beams can be dangerous because of the weak tensile strength – rock unit must be homogeneous and composed of resistant minerals

Location

CONTACT INFO